Free shipping on all orders above Ksh500 to Nairobi CBD via Chania Travellers Sacco.

Arduino MKR GSM 1400

Arduino MKR GSM 1400
Arduino MKR GSM 1400 has been designed to offer a practical and cost effective solution for makers seeking to add global GSM connectivity to their projects with minimal previous experience in networking. It is based on the Atmel SAMD21 and a SARAU201 GSM module. 


The design includes the ability to power the board using a LiPo battery or external power source rated 5V. Switching from one source to the other is done automatically. A good 32 bit computational power similar to the Zero board, the usual rich set of I/O interfaces, gobal GSM communication and the ease of use of the Arduino Software (IDE) for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power (5V) to the board. 


During cellular transmissions, the peak current required by the board will exceed 500mA. This is in excess of what can be sourced by a standard USB port, so it is MANDATORY to have a 1500 mAh or higher LiPo battery plugged all the time, the current provided by the USB port will be supplemented by the battery.  When powering the board using Vin, a 5V power supply that can supply at least 2A is required


Warning: Unlike most Arduino & Genuino boards, the MKR GSM 1400 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.


Technical Specs
Microcontroller SAMD21 Cortex-M0+ 32bit low power ARM MCU
Board Power Supply (USB/VIN) 5V
Supported Battery(*) 3.7V LiPo
Circuit Operating Voltage 3.3V
Digital I/O Pins 8
PWM Pins 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19)
UART 1
SPI 1
I2C 1
Analog Input Pins 7 (ADC 8/10/12 bit)
Analog Output Pins 1 (DAC 10 bit)
External Interrupts 8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17)
DC Current per I/O Pin 7 mA
Flash Memory 256 KB
SRAM 32 KB
EEPROM no
Clock Speed 32.768 kHz (RTC), 48 MHz
LED_BUILTIN 6
Full-Speed USB Device and embedded Host
Antenna power 2dB
Carrier frequency GSM 850 MHz, E-GSM 1900 MHz, DCS 1800 MHz, PCS 1900 MHz
Working region Global
Length 67.64 mm
Width 25 mm
Weight 32 gr.
SIM Size Micro

Write a review

Please login or register to review
  • Views: 151
  • Product Code: Arduino MKR GSM 1400
  • Availability: In Stock
  • KES 9,000.00

Tags: Arduino MKR GSM 1400

The GPRS/GSM Shield provides you a way to use the GSM cell phone network to receive data from a remo..
KES 4,500.00
Atmel's ATMega328P 8-Bit Processor is in a 28 pin DIP package. It's like the ATmega168, with do..
KES 350.00 KES 300.00
Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition..
KES 3,000.00 KES 2,200.00
The DHT-22 is a low cost humidity and temperature sensor with a single wire digital interface. The s..
KES 900.00 KES 650.00
Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in..
KES 100.00 KES 40.00
This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measu..
KES 400.00 KES 300.00
OverviewSensitive to flame spectrumFeatures wide range voltage comparator LM393Adjustable sensitivit..
KES 200.00 KES 150.00

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

Name
Email
Phone
Comments