Stepper Motor Driver High Current DRV8825

Stepper Motor Driver High Current DRV8825

This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet (1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section below for more information). Here are some of the driver’s key features:

  • Simple step and direction control interface
  • Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
  • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
  • Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
  • 45 V maximum supply voltage
  • Built-in regulator (no external logic voltage supply needed)
  • Can interface directly with 3.3 V and 5 V systems
  • Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
  • Short-to-ground and shorted-load protection
  • 4-layer, 2 oz copper PCB for improved heat dissipation
  • Exposed solderable ground pad below the driver IC on the bottom of the PCB

Write a review

Please login or register to review
  • Views: 5393
  • Product Code: DRV8825
  • Availability: In Stock
  • KES 300.00

Tags: stepper motor driver

    Holding Torque: 4000g.cm (40N.cm)     Type: Hybrid   &..
KES 1,500.00
This breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver features adjustab..
KES 200.00
This component is ideally suited to projects requiring controlled rotation. This is the 42BYGHW609 s..
KES 2,500.00
OverviewThe 42BYGHW811 stepper motor is suitable for use with CNC or 3D printers.Specifications..
KES 2,500.00
Stepper Motor Flexible Coupling Connect this to that with a set-screw coupler. These couplers are..
KES 300.00
The Arduino Mega 2560 is a microcontroller board based on the ATmega 2560 . It has 54 digi..
KES 1,600.00
This mount will fit any NEMA-17 motor (with 31mm hole spacing) with four screws. There's two 30mm lo..
KES 300.00
Breadboard including power supply. The power supply can directly take power from DC wall plug or USB..
KES 300.00
This plug and play wireless USB 11N nano wifi dongle will get your Raspberry Pi hooked up to the int..
KES 800.00
Atmel's ATMega328P 8-Bit Processor is in a 28 pin DIP package. It's like the ATmega168, with do..
KES 350.00 KES 300.00
Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition..
KES 3,000.00 KES 2,200.00
The DHT-22 is a low cost humidity and temperature sensor with a single wire digital interface. The s..
KES 900.00 KES 650.00
Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in..
KES 100.00 KES 40.00
This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measu..
KES 400.00 KES 300.00
OverviewSensitive to flame spectrumFeatures wide range voltage comparator LM393Adjustable sensitivit..
KES 200.00 KES 150.00

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

Name
Email
Phone
Comments