This MOV is suitable for 220V AC line protection in a typical electronic devices against voltage surges and spikes, such as those generated by inducti..
This OLED it is really small, just 0.91”. It is made of 128x32 individual blue OLED pixels, each one is turned on or off by the controller chip. Becau..
This breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver features adjustable current limiting, over-current and over-tempera..
This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datashe..
The Arduino CNC Shield makes it easy to get your CNC projects up and running in a few hours. It uses opensource firmware on Arduino to control 4 stepp..
Ideal for development and prototyping work, Stripboard (Veroboard) is designed primarily for hard wiring of discrete components, typically in analogue..
This mount will fit any NEMA-17 motor (with 31mm hole spacing) with four screws. There's two 30mm long slots, 30mm apart so you can easily attach it. ..
The WeMos lithium battery shield provides a means of powering your microcontroller project from a single cell (3.7V) lithium battery. The shield conta..
The Arduino community has come up with the latest revision for the Uno board. It is a beautifully designed board not only from its looks but has some ..
This is our heat shrink kit. We use it for all sorts of handy projects. Use it to reinforce connections, protect devices, and electrically isolate exp..
If you've started designing your own PCBs in Eagle or KiCad and want to make your PCB a reality, you may start out with an etching system to pattern o..
If you've started designing your own PCBs in Eagle or KiCad and want to make your PCB a reality, you may start out with an etching system to pattern o..
DESCRIPTIONThe TB6560 single motor driver board is based on the TB6560AHQ chip. It will significantly increase torque and ease of configuration of lar..
GT 3GT Type Timing pulleys for High Accuracy Positioning.This 20 Teeth 3GT Pulley Timing pulleys with small backlash. Suitable for positioning ,CNC ma..
This is the big kahuna from Mean Well, a 350W single output switching power supply. This power supply is extremely reliable and beefy, able to output ..
This is an LM2596S DC-DC buck converter step-down power module with high-precision potentiometer, capable of driving a load up to 3A with high efficie..
Ensure optimal performance of your electronic device with the use of this EDR-120-24 AC to DC power supply from Mean-Well. It has a voltage of 24 V an..
This DC/DC step-down voltage converter is based on MP1584, it converts input voltage between 4.5V and 28V into a smaller voltage between 0.8V and 18V,..
Breadboard including power supply. The power supply can directly take power from DC wall plug or USB port and outputs are selectable between 5V or 3.3..
A row of headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs, general custom headers or for Arduino Prototype Shield.
..
These are 20cm and 10 cm long jumper wires terminated as male to male. Use these to jumper from any female header on any board. Multiple jumpers can b..
Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be s..
Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be s..
Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be s..
This jaw type half-coupling can be used to connect a 6mm shaft to another shaft 8mm. It is held in place by two set screws, and fits together with ano..
Connect this to that with a set-screw coupler. These couplers are made of machined aluminum and have a spiral cut that makes them slightly flexible so..
Stepper Motor Flexible CouplingConnect this to that with a set-screw coupler. These couplers are made of machined aluminum and have a spiral cut that ..
This jaw type half-coupling can be used to connect a 6mm shaft to another shaft 10mm. It is held in place by two set screws, and fits together with an..
This is a great first stepper motor, good for small projects and experimenting with steppers. This uni-polar motor has a built in mounting plate with ..
This is a great first stepper motor, good for small projects and experimenting with steppers. This uni-polar motor has a built in mounting plate with ..
This breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver features adjustable current limiting, over-current and over-tempera..
This component is ideally suited to projects requiring controlled rotation. This is the 42BYGHW609 stepper motor designed to the NEMA 17 standard. The..
DESCRIPTIONThe TB6560 single motor driver board is based on the TB6560AHQ chip. It will significantly increase torque and ease of configuration of lar..