AM2315 - ENCASED I2C TEMPERATURE/HUMIDITY SENSOR

AM2315 - ENCASED I2C TEMPERATURE/HUMIDITY SENSOR

The AM2315 is a digital I2C humidity - temperature sensor that is mounted in a protective housing. It is not waterproof but sufficient to provide some protection to both sensors mounted inside. It use the DS18B20 along with a capacitive humidity sensor. It has it's own controller that provides a I2C interface to both of these sensors. We cannot change the address of device so it only supports one device per I2C bus. It is supplied with two mounting brackets depending on how you want to physically mount the device.

Simply connect the red wire to 5V power, black to ground, yellow wire to your i2c data pin, and the white wire to the i2c clock pin. You cannot change the i2c address so only one sensor per i2c bus. Two ~10Kohm pullup resistors are required for use, connect from the SDA and SCL lines to the power wire, the pullup resistors are not included!

TECHNICAL DETAILS

 
3.5 to 5.5V power and I/O
10 mA max current use during conversion (while requesting data)
Good for 0-100% humidity readings with 2% accuracy
Good for -20 to 80°C temperature readings ±0.1°C typical accuracy
0.5 Hz update rate
Body size 98mm x 16mm diameter (4" x 0.9" )
4 wires 20 inches long
Weight: 82.64g
This board/chip uses I2C 7-bit address 05C.


AM2315 datasheet

Tutorial

Write a review

Note: HTML is not translated!
    Bad           Good

Captcha

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Aliquam iaculis egestas laoreet. Etiam faucibus massa sed risus lacinia in vulputate dolor imperdiet. Curabitur pharetra, purus a commodo dignissim, sapien nulla tempus nisi, et varius nulla urna at arcu.Lorem ipsum dolor sit amet, consectetur adipiscing elit. Aliquam iaculis egestas laoreet. Etiam faucibus massa sed risus lacinia in vulputate dolor imperdiet. Curabitur pharetra, purus a commodo dignissim, sapien nulla tempus nisi, et varius nulla urna at arcuLorem ipsum dolor sit amet, consectetur adipiscing elit. Aliquam iaculis egestas laoreet. Etiam faucibus massa sed risus lacinia in vulputate dolor imperdiet. Curabitur pharetra, purus a commodo dignissim, sapien nulla tempus nisi, et varius nulla urna at arcu. 

  • Views: 1629
  • Product Code: AM2315
  • Availability: In Stock
  • KES 2,500.00

Tags: temperature humidity sensor

The DHT-22 is a low cost humidity and temperature sensor with a single wire digital interface. The s..
KES 900.00
Features: Size: 28mm x 12mm x 8mm Chip: DHT11 temperature and humidity sensor Operating voltage: ..
KES 250.00
The DHT11 Temperature and Humidity sensor module is designed to detect the surrounding environment f..
KES 450.00
Take your gardening project to the next level with a SHT-10 based soil sensor. The sensor includes a..
KES 3,000.00
The stunning new Raspberry Pi 3 Model B has landed. This third generation model maintains the same p..
KES 6,000.00
Pi-View is a high quality, high performance, convenient and compact electronic device which converts..
KES 1,600.00
Now that you've finally got your hands on a Raspberry Pi® , you're probably itching to make some fun..
KES 1,000.00
The Official Raspberry Pi Power Supply - Shipped with easily interchangeable heads for the UK, US, E..
KES 2,000.00
A 20cm, 40pcs wire cable connector from dupont. Male to male terminated. ..
KES 100.00
A 20cm, 40pcs wire cable connector from dupont. Male to Female terminated. ..
KES 100.00
The Arduino Mega 2560 is a microcontroller board based on the ATmega 2560 . It has 54 digi..
KES 2,000.00 KES 1,600.00
1. Features 1). ATMega 32U4 running at 5V/16MHz 2). Supported under IDE v1.0.1 3). On-Board micro..
KES 1,000.00 KES 700.00
Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition..
KES 2,200.00 KES 2,200.00
Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition..
KES 3,000.00 KES 2,200.00
Breadboard including power supply. The power supply can directly take power from DC wall plug or USB..
KES 300.00 KES 250.00
This is a blank copper board perfect for pcb prototyping/printing. It is made from FR4 glass fibre..
KES 250.00 KES 200.00