TB6600 Stepper Motor Driver

TB6600 Stepper Motor Driver

INTRODUCTION

What is a stepper motor?
Stepper motor is a brushless DC electric motor that divides a full rotation into a number of equal steps The motor's position can then be commanded to move and hold at one of these steps.

How to control a stepper motor?
The fast way to control a stepper motor is just using a stepper motor driver (controller). And TB6600 arduino is just what you need.

TB6600 arduino is an easy-to-use professional stepper motor driver, which could control a two-phase stepping motor. It is compatible with Arduino and other microcontrollers that can output a 5V digital pulse signal. TB6600 arduino stepper motor driver has a wide range power input, 9~42VDC power supply. And it is able to output 4A peak current, which is enough for the most of stepper motors.

The stepper driver supports speed and direction control. You can set its micro step and output current with 6 DIP switch. There are 7 kinds of micro steps (1, 2 / A, 2 / B, 4, 8, 16, 32) and 8 kinds of current control (0.5A, 1A, 1.5A, 2A, 2.5A, 2.8A, 3.0A, 3.5A) in all. And all signal terminals adopt high-speed optocoupler isolation, enhancing its anti-high-frequency interference ability.

As a professional device, it is able to drive 57, 42-type two-phase, four-phase, hybrid stepper motor.

Note: this is a newest upgrade version of TB6600 stepper motor driver.
TB6600 Stepper Motor Driver - DFRobot

 DIY Alarm using Home Assistant, Konnected, and Sonoff RF Bridge

TB6600 5A Stepper motor driver and Arduino


Hardwares you needed:

Bipolar Stepper Motor with Planet Gear Box
TB6600 Stepper Motor Driver

FEATURES

  • Support 8 kinds of current control
  • Support 7 kinds of micro steps adjustable
  • The interface adopts high-speed optocoupler isolation
  • Automatic semi-flow to reduce heat
  • Large area heat sink
  • Anti-high-frequency interference ability
  • Input anti-reverse protection
  • Overheat, over current and short circuit protection
  • SPECIFICATION

  • Input Current: 0~5A
  • Output Current: 0.5-4.0A
  • Control Signal: 3.3~24V
  • Power (MAX): 160W
  • Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32
  • Temperature: -10~45℃
  • Humidity: No Condensation
  • Dimension: 96*56*33 mm/ 3.78*2.2*1.3 inches
  • Weight: 0.2 kg
  • Drive IC: TB67S109AFTG
  • Write a review

    Please login or register to review
    • Views: 119
    • Product Code: TB6600 Stepper Motor Driver
    • Availability: In Stock
    • KES 1,000.00

    Tags: TB6600 Stepper Motor Driver

        Holding Torque: 4000g.cm (40N.cm)     Type: Hybrid   &..
    KES 1,500.00
    This bipolar Nema 23 stepper  motor with 1.8 deg. step angle (200 steps/revolution). Each ..
    KES 3,300.00
    DESCRIPTIONThe TB6560 single motor driver board is based on the TB6560AHQ chip. It will significantl..
    KES 1,300.00
    Atmel's ATMega328P 8-Bit Processor is in a 28 pin DIP package. It's like the ATmega168, with do..
    KES 350.00 KES 300.00
    Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition..
    KES 3,000.00 KES 2,200.00
    The DHT-22 is a low cost humidity and temperature sensor with a single wire digital interface. The s..
    KES 900.00 KES 650.00
    Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in..
    KES 100.00 KES 40.00
    This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measu..
    KES 400.00 KES 300.00
    OverviewSensitive to flame spectrumFeatures wide range voltage comparator LM393Adjustable sensitivit..
    KES 200.00 KES 150.00

    The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

    Name
    Email
    Phone
    Comments