IRF1010E N channel Mosfet

IRF1010E N channel Mosfet

IRF1010E is an n-channel enhancement MOSFET designed for high speed switching applications.  It also has low turn ON resistance. Like any other MOSFET the IRF1010E is voltage controlled device and MOSFET state is decided by GATE voltage.


IRF1010E Pin Configuration

It has three pins namely GATE, DRAIN and SOURCE. The pin configuration of IRF1010E is given below.

Pin Number

Pin Name




Normally connected to GROUND



Normally connected to LOAD



Normally used as TRIGGER to turn ON the MOSFET.


IRF1010E Features and Specifications

  • Advanced process technology
  • Fully avalanche rated
  • Fast switching
  • Fifth generation HEXFET
  • Maximum voltage across DRAIN and SOURCE: 60V
  • Maximum continuous current allowed trough DRAIN: 81A
  • Maximum pulsed DRAIN current: 330A
  • Maximum voltage across GATE and SOURCE:20 V
  • Maximum operating Temperature: 175ºC
  • Maximum power dissipation: 170Watt


IRF1010E Equivalents

IRF1407, IRFB4110, IRFB4110G, IRFB4115, IRFB4310Z, IRFB4310ZG, IRFB4410


Where to Use IRF1010E?

There are many reasons for using IRF1010E, here are a few:

  • When you want a high speed SWITCHING device for MEDIUM POWER LOADS. As mentioned above IRF1010E is specially designed for high speed switching of medium power loads so it is fairly popular in those areas.
  • When you want low drop switching device. The MOSFET has very low turn ON resistance leading to very low drop during ON condition, which is a must condition in some applications.
  • With low drop the MOSFET power loss will be less. With less power loss the efficiency of the system will be more. So the MOSFET is preferred for high efficiency applications.


How to use IRF1010E

IRF1010E MOSFET can be used like any other power MOSFETs, so let us consider an example circuit for IRF1010E as shown below.

IRF1010E Circuit Diagram

In the above circuit we are using IRF1010E as a simple switching device. In the circuit we are using a small motor as the LOAD. The TRIGGER for turning ON the MOSFET is provided by CONTROL UNIT (NOT MICROCONTROLLER as MICROCONTROLLER cannot provide voltages higher than +5V).The SOURCE is grounded. The power source here is +12V battery.

CONTROL UNIT trigger voltage = V1

GATE voltage = V2

The resistors R1 and R2 here form a voltage divider circuit to provide appropriate voltage at GATE. So they are chosen based on CONTROL UNIT trigger voltage (V1) and MOSFET GATE threshold voltage.

For example consider the CONTROL UNIT provides pulses of voltage +12V. Also for turning ON the MOSFET IRF1010E completely we need GATE voltage of 10V.

So V1 =+12V and V2 = +10V

We can choose R1 and R2 as,









With the voltage divider circuit formed by any set of above table will give exact +10V at MOSFET GATE. This Resistor set could be chosen without considering the current draw from MOSFET as it is negligible. These resistances could be chosen approximately for normal applications.

In the circuit above under normal conditions the MOSFET will be OFF as these will be no GATE voltage. And when MOSFET is OFF the complete VCC appears across it. In this case the DRAIN current will be zero. Since DRAIN current is zero the MOTOR will sit idle.

When the CONTROL UNIT provides voltage pulses there will be GATE voltage. With GATE voltage being present the MOSFET gets tuned ON. With that there will be DRAIN current which flows through MOTOR. Having current flow the MOTOR stars rotating. The MOTOR will be keep rotating until there will be GATE voltage.

When the CONTROL UNIT output goes LOW the GATE voltage also becomes LOW. The MOSFET gets turned OFF when the GATE voltage drops below the threshold voltage. Under OFF state the DRAIN current also becomes ZERO, bringing MOTOR to STOP.

By above scenario you can tell the MOSFET is used as switching device with trigger being provided by control unit. This way we can use IRF1010E as a switching device in any application. The circuit used above is a simple testing circuit and is not an application circuit. The application circuit must have required arrangements like HEAT SINK, FLYBACK DIODE etc.



  1. Basically any switching applications
  2. speed control units
  3. Lighting systems
  4. PWM applications
  5. Relay drivers
  6. Switch mode power supply



All measurements are in millimeters (inches)

IRF1010E MOSFET Dimensions

Component Datasheet

Write a review

Please login or register to review
  • Views: 2788
  • Product Code: IRF1010E
  • Availability: In Stock
  • KES 130.00

Tags: Mosfet, N channel, IRF1010

These 5mm units have four pins – Anode is the longest pin. One for each colour(Red, Green, Blue..
KES 10.00
The A3144 is an integrated Hall effect latched sensor. That’s nice but what does it do? Holding a ma..
KES 100.00
  Support Micro SD Card, Micro SDHC card (high-speed card) The level conversion circuit b..
KES 300.00
The CD74HC154E is a 4-to-16 line high speed CMOS Decoder/Demultiplexer with two enable inputs, E1 an..
KES 150.00
SpecificationsPower (Watts) 0.25 (1/4 Watts)Resistance 1K OHMSTolerance +- 1%Resistor Type metal Fil..
KES 5.00
SpecificationsPower (Watts) 0.25 (1/4 Watts)Resistance 10K OHMSTolerance +- 1%Resistor Type metal Fi..
KES 5.00
Model: 6LR61Size: 9vJacket: Aluminium Foil batteryCompliance: CE ROHSCapacity: 270ohm,24h/d,720minut..
KES 150.00 KES 120.00
The Arduino Mega 2560 is a microcontroller board based on the ATmega 2560 . It has 54 digi..
KES 2,000.00 KES 1,700.00
The Arduino community has come up with the latest revision for the Uno board. It is a beautifully de..
KES 1,200.00 KES 1,200.00
Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition..
KES 3,000.00 KES 2,200.00
Specifications Model: MB-102 Dimension: 165mm x 55mm x 10mm Tie Points: 830 Tie Points con..
KES 200.00 KES 180.00
The DHT-22 is a low cost humidity and temperature sensor with a single wire digital interface. The s..
KES 650.00 KES 550.00

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.