- Action Cameras & Accesories
- Development Platforms
- Electronic Components
- LED Panels & Accesories
- Solenoid Devices
- Integrated Circuits
- Mini PC
- Robotics & Aeronautics
- Wireless devices
The Arduino community has come up with the latest revision for the Uno board. It is a beautifully designed board not only from its looks but has some really neat innovations and redesigns. The Arduino Uno is a microcontroller board based on the ATmega328. Arduino is an open-source, prototyping platform and its simplicity makes it ideal for hobbyists to use as well as professionals. The Arduino Uno has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
Want to learn how to work with electronics and microcontrollers but need a little help? You’ve come to the right place! This bundle is designed to get you started quickly and easily on your path of learning electronics. The package includes:
- Arduino Uno R3 Retail Version Including Programming Cable
- Breadboard with power supply module
- Jumper Wire
- 65pc M-M for breadboarding
- 40pc Dupont M-F
- 40pc Dupont F-F
- 0.1uf Ceramic x 2
- 1uf ceramic
- 100uf electrolytic
- 10uf electrolytic
- Transistors & Mosfet
- 2N2222 x 2
- 2N4123 x 2
- Servo Motor SG90
- Micro Dc Motor Brushless
- Wireless Devices
- IR Receiver Diode TSOP1738
- IR Led TX/RX Pair
- RF Receiver Transmitter Kit 315Mhz
- PIR Motion Sensor
- Ultrasonic Sensor HC-SR04
- Light Dependent Resistor
- TCRT5000 Optical Sensor
- Voltage Regulators
- LCD 16 X 2 Display
- LCD serial Adapter
- 7 Segment 2 Digit Display
- 8 X 8 Dot Matrix Display
- Motor driver H bridge SN754410
- LED 5mm diffused assorted colors (15pcs)
- LED RGB Diffused 10mm Common Cathode x 2
- 9V Battery Clip
- DC Jack 2.1mm Plug
- Header Pins Male x 2
- Tact switch x 4
- Shift Register 74HC595
- BCD 7 Segment Decoder IC CD4511
Note: Product list might change from time to time
The Arduino Mega 2560 is a microcontroller board based on the ATmega 2560 . It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Uno.
Arduino Nano is a surface mount breadboard embedded version with integrated USB. It is a small, complete, and breadboard friendly. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard +5V AREF jumper. Physically, it is missing the power jack. The Nano will automatically sense and switch to the higher voltage source of power, there is no need for the power select jumper.
This is the Arduino V2 Pro Mini! It's thin (0.8mm)! This Mini board has an adjustable voltage regulator(you can set the output voltage by yourself) running the 16MHz bootloader ((select 'Arduino Duemilanove w/ 328' within the Arduino software). This Pro Mini V2 does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Uno R3. It's a great board that will get you up and running quickly.
The V2 Pro Mini is like the Arduino Mini (same pin out) but to keep the cost low, all components are SMD components and the PCB is two layer. This board connects directly to the FTDI Basic Breakout board and supports auto-reset. The V2 Pro Mini also works with the FTDI cable but the FTDI cable does not bring out the DTR pin so the auto-reset feature will not work.
ATmega328 running at 16MHz with adjustable voltage regulator(3.3V/5V)
USB connection off board
Max 150mA output
Over current protected
Reverse polarity protected
DC input 5V up to 12V
On board Power and Status LEDs
Less than 2 grams
The Raspberry Pi 3 Media Center Kit with OpenElec is the ideal compact home theatre companion.
OpenELEC provides a complete media center software suite that comes with a pre-configured version of Kodi and third-party addons with retro video game console emulators and DVR plugins.
Included in Kit:
Raspberry Pi 3 Model B
Class10 8GB MicroSD with OpenElec 7.0.1
Wireless Mini Keyboard with trackpad (brand may vary)
Official Raspberry Pi USB Power Supply
1m HDMI Cable
Official RasPi Case (colour may vary)
The Intel® Edison is an ultra small computing platform that will change the way you look at embedded electronics. Each Edison is packed with a huge amount of tech goodies into a tiny package while still providing the same robust strength of your go-to single board computer. Powered by the Intel® Atom™ SoC dual-core CPU and including an integrated WiFi, Bluetooth LE, and a 70-pin connector to attach a veritable slew of shield-like “Blocks” which can be stacked on top of each other. It’s no wonder how this little guy is lowering the barrier of entry on the world of electronics!
The on-line Edison SIK Experiment Guide (in the Documents section below) contains step by step instructions of how to connect each circuit with the included parts. Full example code is provided and explained and even includes fritzing diagrams and the required components.
The kit does not require any soldering and is recommended for anyone with an interest in Internet of Things projects or the Intel® Edison in general.
Circuit 1: Hello, World!
Circuit 2: Pushing Some Buttons
Circuit 3: Blinky
Circuit 4: Email Notifier
Circuit 5: Web Page
Circuit 6: RGB LED Phone App
Circuit 7: Speaker
Circuit 8: Temperature and Light Logger
Circuit 9: Weather on an LCD
Circuit 10: Keyboard
Circuit 11: Phone Accelerometer
Circuit 12: Bluetooth Game Controller
1x Intel® Edison
1x SparkFun Block for Intel® Edison - Base
1x SparkFun Block for Intel® Edison - GPIO
1x SparkFun Block for Intel® Edison - ADC
1x Basic 16x2 Character LCD
1x Mini Photocell
1x Temperature Sensor - LM35
1x LED - RGB Diffused Common Anode
20x 100 Ω Resistors
20x 1k Ω Resistors
3x 2N3904 NPN Transistors
1x Piezo Speaker
1x 10k Trimpot
1x USB OTG Cable
1x USB microB Cable
1x Intel® Edison Hardware Pack
30x Jumper Wires
5x Tactile Switches
1x Plastic Electronic components storage box
The Raspberry Pi Camera Module V2 is the new and improved official camera board from the Raspberry Pi Foundation! Custom designed and manufactured by the Raspberry Pi Foundation in the UK, the Raspberry Pi Camera Board V2 features an ultra-high quality 8 megapixel Sony IMX219 image sensor (up from 5MP on the V1 camera board), and a fixed focus camera lens. The V2 camera module is capable of 3280 x 2464 pixel static images, and also supports 1080p30, 720p60 and 640x480p90 video.
The module attaches to Raspberry Pi by way of a 15 Pin Ribbon Cable, to the dedicated 15-pin MIPI Camera Serial Interface (CSI), which was designed especially for interfacing to cameras. The CSI bus is capable of extremely high data rates, and it exclusively carries pixel data to the BCM2835 processor. A 150mm CSI cable is included with every camera.
The board itself is tiny, at around 25mm x 23mm x 9mm, and weighs just over 3g, making it perfect for mobile or other applications where size and weight are important.
The Raspberry Pi Camera Board V2 Features:
Fixed focus lens on-board
150mm CSI camera cable included
8 megapixel native resolution sensor-capable of 3280 x 2464 pixel static images
Supports 1080p30, 720p60 and 640x480p90 video
Size 25mm x 23mm x 9mm
Weight just over 3g
Connects to the Raspberry Pi board via a short ribbon cable (supplied)
Camera v2 is supported in the latest version of Raspbian, Raspberry Pi's preferred operating system
The Intel® Edison is an ultra small computing platform that will change the way you look at embedded electronics. Each Edison packs a huge amount of tech goodies into a tiny package while still providing the same robust strength of your go-to single-board computer. Powered by the Intel® Atom™ SoC dual-core CPU and including an integrated WiFi, Bluetooth LE and 70-pin connector to attach a veritable slew of shield-like “Blocks,” which can be stacked on top of one another. It’s no wonder how this little guy is lowering the barrier of entry on the world of electronics!
The Intel Edison packs a robust set of features into its small size, delivering great performance, durability and a broad spectrum of I/O and software support. Those versatile features help meet the needs of makers, inventors and beginners. This is a module with a high-speed processor and WiFi and Bluetooth radios onboard. Its low power and small footprint make it ideal for projects that need a lot of processing power but don’t have the ability to be near a larger power source or have a large footprint.
If you are looking to add a little more stability to your Intel Edison stack, check out this Hardware Pack. It will provide you with increased mechanical strength for stacking Blocks on your Edison!
Dimensions: 35.5 × 25.0 × 3.9 mm (1.4 × 1.0 × 0.15 inches) Max
Intel Atom system-on-a-chip (SoC) based on leading-edge 22nm Silvermont microarchitecture, including a dual-core CPU and single-core microcontroller (MCU)
Integrated WiFi, Bluetooth LE, memory and storage
Support for more than 30 industry-standard I/O interfaces via a 70-pin connector
Support for Yocto Linux, Arduino, Python, Node.js and Wolfram
Open source community software tools enabling ease of adoption and inspiring third-party app developers to build apps for consumers.
EDI1.SPON.AL.S (System-On-Modules, SOM, Edison Module IoT Internal Antenna)
IO Expansion Shield is one of the market favourites. Fast robotics prototyping made affordable and simple thanks to this design. Soldering and wiring often becomes a problem when a bridged connection happens and components break sometimes, increasing time and cost. The IO Expansion Shield for Edison extends Edison's powerful scope into sensing the physical world, and prepares it ready for interaction through wireless communication. This IO expansion board for Edison is compatible with Arduino open source platform and Linux, and supports Java and C development environment. It can also be used as a standalone communication platform for software like flash, processing, Max/MSP and VVVV.
The IO Expansion Shield for Edison adopts DFRobot's classic color code for sensors/actuators input/output. The 3 pin format for Signal, Voltage and Ground is extremely intuitive, especially if used altogether with our increasingly large range of modules, sensors and devices that just fit.
Operating Voltage: 5V
Output Voltage: 5V/3.3V
Input Voltage(limits): 6-20V
Digital I/O pins: 14
DC Current per I/O Pin: 10mA
Digital I/O pins: D0-D13
PWM Output interface: 4 (Digital pins D3, D5, D7 and D9)
Support USB power and external power supply switch
Support 1 x I2C interface
Support Broadcom 43340 802.11 a/b/g/n dual band (2.4G and 5GHz) WiFi
Support Bluetooth 4.0
MAX7219 is a kind of integrated serial input/ output common cathode display driver, it connects microprocessor and 8-digit seven period of digital LED display, also can be connected to the bar graph display or 64 independent LED.
1. The left of the module is input port, the right is output port
2. Only input port to the CPU when you control a single module
MAX7219 Red LED Dot Matrix Module MCU Control Module Specifications:
1. Color: Green + White
2. Material: FR4
3. Working Voltage: 5V
4. Size: 5x3.2x1.5cm
5. Light Color: Red
6. Hole Quantity: 4pcs
7. Hole Diameter: 3mm
Note: These come as a DIY kit. You will have to solder the components on the board
1X PCB board
1X 24P IC socket
1X DIP MAX7219 chip
1X 10uF electrolytic capacitor
1X 0.1uF a ceramic capacitor
1X 10K resistor
1X 3mm 8 x 8 common cathode a red dot
- Product Category: LED Displays
- RoHS: Yes
- Datasheet: N/A
- Display Type: 7 Segment
- Number of Digit / Alpha: 4
- Color: RED
- digit / alpha 'Height' (inch): 0.56
- Common Pin: Common Cathode
- Face Color: Black
- Len Epoxy Color: White Diffused
Make a small linear display with a glowing blue color using this elegant LED bargraph. Only 1" long, it is quite visible but not so large it wont plug into a breadboard! 10 LEDs are contained in the plastic body. This display is bright, beautiful and funky with nice diffused rectangular lenses for a striking look. There are 20 pins,10 on each side, with 0.1" spacing so you can easily plug it into a breadboard with plenty of space for wiring left over.
We know this looks like a lot of our other LEDs, but it’s not! This is a PTH Addressable RGB LED with a WS2812 control IC built right into the LED. This PTH version is incredibly similar to its SMD cousin, except it is a lot simpler to solder into your project and is in a diffused 8mm package. This RGB LED has the control IC moved into the actual LED, so we wanted to offer this amazing product to you! They’re great when you need a lot of color from not a lot of board space, now more so than ever.
If you are looking for a great addressable LED in the more common LED form factor, then this is the perfect choice for you.
Note: MInimum order of 5.
Power Supply: DC 4.5V - 6V
Internal Frequency: 800K Hz
Single Wire Single Transmission
Are you looking to add a lot of color to your project? These large 32x16 RGB LED panels are an awesome place to start. You can create animations, games, or all sorts of other fun displays with them. Yes, you read that right: a 32x16 LED matrix, that’s 512 LEDs on a 7.5" x 3.75" board. On top of all that, thanks to two IDC connectors, and a seamless frame, these panels can be daisy chained together to form even bigger LED displays.
These panels require a regulated 3.3-5V supply for power which needs to be able to source a good amount of current – up to 2A in the worst case. Included with each panel is a 0.15" pitch 4-pin polarized connector power cable which is terminated with both a female polarized connector, and a pair of spade terminals. Needless to say, if you are looking for a large, cheap, and easy to use RGB LED matrix you’ve come to the right place.
Note: These displays were intended for use with FPGAs and high-speed processors. We’ve found that 16MHz is about the slowest processor that can drive these adequately. If you want to daisy-chain them together, you will need more speed and more RAM.
512 RGB LEDs
1/8 Scan Rate
Dual IDC Connectors for Daisy Chaining
3.3-5V Supply Voltage
1x 32x16 RGB LED Panel
1x 0.15" Pitch 4-pin Power Cable w/ Spade Connectors
1x 16-pin (2x8) Ribbon Cables
5v 4-channel relay interface board. It can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM and so on.
1-Channel Relay interface board,
Each one needs 15-20mA Driver Current
Equiped with high-current relay : DC30V 10A AC250V 10A
Standard interface that can be controlled directly by microcontroller
A high quality AC to DC 9V 1000mA wall power supply.
These will power most projects that don't require more than 1A of current. Center-positive 5.5x2.1mm barrel connector.
Normally closed solenoid valves open when electrical current is applied and return to the closed position when no current is present.
Port Size:3/4'' BSPP
Coil resistance: 4.75KΩ±0.25KΩ (Temp.200C) 4.75KΩ±0.25KΩ (Temp.200C)
Operation Mode: NC (Normally Closed)
Working Media: Water, Air, Natural Gas, Low Viscosity Fluid, etc.
Media Temperature Range: 1C-75C
Response Time: Open≤0.15s Close≤0.3s
Working Pressure Range: 0.02Mpa-0.8Mpa
Flow characteristics: 0.02Mpa≥3 L/min, 0.1Mpa≥12 L/min,0.8Mpa≥35L/min
Ever want to build your own weather station? This iot weather station kit includess anemometer, wind vane and rain bucket. The serial communication method provides good compatibility and makes it easy to use with most controllers in the market.
Together with other components, this iot weather station kit can be widely used in measureing wind/rain in engineering, railways, docks, power plants, meteorological, cableway, environment study, agriculture, energy monitoring, health study with corresponding signal output.
Also, it is compatible with Arduino devices.
Operating voltage: 5V
Temperature range: -40~80℃
Humidity range: 0~99%
Package Dimension: 20*18*30 CM (7.87*7.09*11.81")
Wind vane x1
Rain bucket x1
Sensor Board x1
Stainless steel studdle (30CM)(11.81") x2
Stainless steel studdle (29CM)(11.42") x1
component package x1
Working Power: AC100V~250V, 50/60HZ
Load Power: LED≤40W, Energy Saving≤60W, Incandescent≤100W, Fan≤50W
Standby power 0.0088W
Sensor Distance: 6~10m
Sensor Angle: 110~140degree
Application: Corrido,toilet,basement, warehouse,garage ,and other places of automatic lighting, exhaust fan convulsions and other automatic control electrical, can be used for security purposes at the same time.
The turbidity sensor detects water quality by measuring level of turbidity. It is able to detect suspended particles in water by measuring the light transmittance and scattering rate which changes with the amount of total suspended solids (TSS) in water. As the TTS increases, the liquid turbidity level increases.
This turbidity sensor have both analog and digital signal output modes. You can select the mode according to the MCU as threshold is adjustable in digital signal mode.
Turbidity sensors can be used in measurement of water quality in rivers and streams, wastewater and effluent measurements, sediment transport research and laboratory measurements.
Note: the top of the probe is not waterproof
Operating Voltage: 5V DC
Operating Current: 40mA (MAX)
Response Time: <500ms
Insulation Resistance: 100M (Min)
Analog output: 0-4.5V
Digital Output: High/Low level signal (you can adjust the threshold value by adjusting the potentiometer)
Operating Temperature: 5℃~90 ℃
Storage Temperature: -10℃~90℃
Adapter Dimensions: 38mm*28mm*10mm/1.5inches *1.1inches*0.4inches
Take your gardening project to the next level with a SHT-10 based soil sensor. The sensor includes a temperature/humidity sensor module from Sensiron in a sinter metal mesh encasing. The casing is weatherproof and will keep water from seeping into the body of the sensor and damaging it, but allows air to pass through so that it can measure the humidity (moisture) of the soil. It is designed to be submersible in water, but it's always best to avoid long-term (over 1 hour at a time) submersion, if you need something that can be submerged for over an hour you may want to find a different sensor. It can also be simply placed outside for exterior weather sensing.
Humidity readings have 4.5% precision, temperature is 0.5% precision. A microcontroller is required to interface. The sensor is not washed after reflow and is rehydrated according to datasheet requirements.
The sensor is essentially just a Sensiron SHT-10 with the 4 data/power wires brought out so any SHT-1X code for a microcontroller will work. The sensor works with 3 or 5V logic. The 1 meter long cable has four wires: Red = VCC (3-5VDC), Black or Green = Ground, Yellow = Clock, Blue = Data. For Arduino, there's a handy Sensiron library with example. For Propeller, there's an SHT1X sensor object. Don't forget to connect a 10K resistor from the blue Data line to VCC.
Water flow sensor consists of a plastic valve body, a water rotor, and a hall-effect sensor. When water flows through the rotor, rotor rolls. Its speed changes with different rate of flow. The hall-effect sensor outputs the corresponding pulse Signal.
Working voltage 5V-24V
Maximum current 15 mA(DC 5V)
Weight 43 g
Flow rate range 1~30 L/min
Liquid temperature 0°C~80°C<120°C
Operating humidity 35%~90%RH
Operating pressure under 1.75Mpa
Store temperature -25°C~+80°C
Store humidity 25%~90%RH
The Standard Servo 3001HB is a great, general-purpose, low-cost standard analog servo from Power HD. Two ball bearings help reduce friction and improve performance. This servo is a replacement for—and upgrade over—the original HD-2360A servo. Servo horns and associated hardware are included.
Key specs at 6 V: 0.12 sec/60°, 61 oz-in (4.4 kg-cm), 43 g.
Size: 40.7 x 20.5 x 39.5 mm
Weight: 43 g
Speed @ 6V: 0.12 sec/60°
Stall torque @ 6V: 4.4 kg·cm
Speed @ 4.8V: 0.15 sec/60°
Stall torque @ 4.8V: 3.5 kg·cm
Lead length: 11 in
Hardware included?: Y
This is the Standard Gripper Kit A, a simple and durable robotics kit that is great for “getting a grip” on pretty much any robotics project! Designed for use with any standard size Hitec or Futaba servo, the gripper kit is easy to assemble and requires only a Phillips Head Screwdriver. This Standard Gripper is capable of opening an impressive 5" wide, has an overall body dimension of 5" long by 3" wide, and offers both 0.77" and 1.5" hub patterns for easy mounting on Actobotics components.
Actobotics is a robotics building system based around extruded aluminum channels, gears, precision shafts, and ball bearings. Thanks to the two standardized hole patterns, nearly all Actobotics components can be intuitively connected together. The wide range of components makes building complex electromechanical prototypes or finished projects a reality.
Note: This kit does NOT include a servo.
Opening Width - 5" (127mm)
Hub Pattern - 0.77" & 1.5"
Want to start building your own robot. Use this platform complete with geared motors and tachometer. Just mount your arduino or microcontroller board and sensors. Simple!
Transparent laser cut chassis
velocity encoder 2 pcs
yellow tires 2pcs
Geared motors 2 pcs
screws and nuts
AA battery compartment
The Turtle 2WD Basic Kit is a perfect platform to build on and to get started with Arduino Robotics. With just a few simple steps of assembling the hardware and tuning the software, and you'll learn all about Arduino, robotics, sensors, bluetooth communication — as well as obstacle avoidance and remote controlling. You can also take it further with your own code to take advantage of the ultrasonic sensor, Romeo All-in-one Bluetooth Microcontroller, IR sensors and LEDs.
The Turtle 2WD Mobile Platform is a small, low-cost mobile platform compatible with standard Arduino microcontrollers. It contains two drive motors, wheels (and rear caster ball), frame and all mounting hardware. It is widely used as self-developed control chasis for Arduino platforms and other control boards. The Turtle 2WD has multiple features such as: two differential drives, near zero turning radius, high-strength aluminum alloy body material, motors and a flexible rubber wheel makes it suitable for indoor flat road surface and flat-platform robot competitions. The top layer includes a standard servo socket and the three optional sensor holder. This three sensor holder fits with our adjustable IR range sensor. The servo can be used for a simple rotation platform, a two degrees of freedom camera holder or even a robotic arm.
Thanks to Romeo BLE, the kit can be controllered by APP (IOS). Simply download an APP GoBLE to enjoy the control from your IOS device.
Board: Arduino UNO
Controller Operating Voltage: 5V
Controller Input Voltage (recommended): 7 ~ 12V
Ultrasonic Sensor Detecting range: 4cm-3m (3-5m is possible, but depending on situations)
Rotation range: 0 - 180
Weight: 480g(Excluding battery)
Maximum Load: 500g
Romeo BLE (Arduino Compatible Atmega 328)(DFR0305) x1
DF05BB Standard Servo (5kg) (SER0020) x1
URM37 V4.0 Ultrasonic Sensor (SEN0001) x1
URM ultrasound mounting bracket （FIT0006） x1
Turtle 2WD chassis x1
Infrared proximity switch bracket （FIT0032） x1
5xAA battery holder x1
PH-2.0 to DC-2.2 adapter x1
Screws KIT x1
Micro DC Geared Motors(FIT0016) x2
Motor Wire x1
Rubber Wheels(FIT0003) x2
Jumper Wires 9" F/F (10 Pack) （FIT0030） x1
Magnet Micro USB Cable 1.2m ( FIT0351-OE) x1
RoMeo V2 [R3] is an All-in-One Arduino based robot board, it is especially designed for robotics applications, and extended devices. Romeo benefits from the Arduino open source platform, it is supported by thousands of open source projects, and can easily be expanded with Arduino Shields. The integrated 2 way DC motor driver and Xbee socket allows you to start your project immediatly without the need for an additional motor driver or wireless shield.
Another improvement of Romeo V2 is that it supports stepper motor control.
The RoMeo V2 [R3] behaves like Arduino Leonardo based on the ATmega32u4 chip,You can program it directly from the Arduino IDE 1.0.1 or later version. Because of the ATmega32U4 as it's sole microcontroller, RoMeo V2 is simple and easy to use. The 32U4 chipset handles the USB directly, code libraries are available which allow the board to emulate a computer keyboard, mouse, and more using the very interesting USB-HID protocol! The best advantage is that ATmega32u4 has two serial ports which allows uploading sketches without removing wireless modules. Debuging is no longer a painful task.
Romeo V2 also improves the power supply, it has now a switch to select power source either from USB or external power.
Romeo V2.2 redesigns the power supply system to improve the stability of the ADC circuit.
Wide operating input voltage
Directly support Xbee and XBee form factor wifi, bluetooth and RF modules
ON/ OFF switch to control the system power from external motor power
3 Digital I/O extensions (D14-D16)
S1 - S5 switch replace jump cap, allows free use for the GPIO.
Micro USB instead of A-B USB connector
Analog sensor extension port: Orange for Signal, Red for Vcc, Black for GND
Note:The analog sensor port pin mapping on RoMeo v2 is different from the old version. Please select Arduino Leonardo board when using Arduino IDE.
DC Supply: USB Powered or External 6V ~ 23V DC
DC Output: 5V(2A) / 3.3V DC
Motor driver Continuous Output Current: 2A
Bootloader: Arduino Leonardo
Compatible with the Arduino R3 pin mapping
Analog Inputs: A0-A5, A6 - A11 (on digital pins 4, 6, 8, 9, 10, and 12)
PWM: 3, 5, 6, 9, 10, 11, and 13. Provide 8-bit PWM output
5 key inputs for testing
Auto sensing/switching external power input
Support Male and Female Pin Header
Built-in Xbee socket
Integrated sockets for APC220 RF Module and DF-Bluetooth Module
Three I2C/TWI Interface Pin Sets (two 90°pin headers)
Two way Motor Driver with 2A maximum current
One Stepper Motor Drive with 2A maximum current
Size: 89 x 84 x 14mm (3.50 x 3.31 x 0.55")