This Infrared obstacle/object detection sensor is super easy to use. It comes with on board potentiometer to adjust the sensitivity. The output is dig..
The all new NodeMCU-32S with ESP32/CH340C Wifi Development Board - TYPE CThe NodeMCU-ESP32 is an ideal choice for effortless prototyping, offering eas..
The Relay is a digital normally open switch that controls a relay capable of switching much higher voltages and currents than your normal Arduino boar..
Ideal for development and prototyping work, Stripboard (Veroboard) is designed primarily for hard wiring of discrete components, typically in analogue..
These are 20cm and 10 cm long jumper wires terminated as male to male. Use these to jumper from any female header on any board. Multiple jumpers can b..
The A3144 is an integrated Hall effect latched sensor. That’s nice but what does it do? Holding a magnet near the sensor will cause the output pin to ..
The HT 12E Encoder ICs are series of CMOS LSIs for Remote Control system applications. They are capable of Encoding 12 bit of information which consis..
This is an easy, simple to use Passive IR (PIR) sensor – it only needs a single I/O pin on a microcontroller.or can be easily interfaced with relay or..
Jumper wires are simply wires that have connector pins at each end, allowing them to be used to connect two points to each other without soldering. Ju..
It's compatible with breadboard, and you can easy to make your protype with the square led.Feature:Uniform light emitting area. Easily mounted on P.C...
The driver circuit based on 3 MBI5168 constant current sink drivers and a M54564 darlington source driver, the Colorduino pairs the M54564 with a sing..
The 8x8 LED dot matrix kit has many applications in real life, such as various types of electronic display, panels for indoor or semi outdoor sign boa..
Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be s..
We are big fans of these diffused green LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be seen in daytime, and ..
Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be s..
Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be s..
Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be s..
Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be s..
These color-changing LEDs take the work out of creating crazy, flashy, blinky… ness. Simply apply power and the LED will cycle through the RGB colorsp..
These color-changing LEDs take the work out of creating crazy, flashy, blinky… ness. Simply apply power and the LED will cycle through the RGB colorsp..
This RGB LED strip allows you to individually control all 32 RGB LEDs on a waterproof, self-adhesive strip. Each LED has its own WS2801 IC and current..
These are sealed addressable 5 meter long 5V RGB LED strips that come packed with 60 WS2812s per meter. Each of these strips are enclosed by a flexibl..
24 ultra bright smart LED NeoPixels are arranged in a circle. The rings are 'chainable' - connect the output pin of one to the input pin of another. U..
This is a FPC LED stick, a small chainable board with eight 5050 WS2812 RGB LEDs. The WS2812s are each addressable as the driver chip is located insid..
MAX7219 is a kind of integrated serial input/ output common cathode display driver, it connects microprocessor and 8-digit seven period of digital LED..
These fancy new LED strips are even more fun and glowy. There are 60 RGB LEDs per meter, and each LED can be controlled individually. You can set the ..
This is the NeoPixel NeoMatrix a large board with 64 WS2812 RGB LEDs arranged in an 8x8 matrix. Each LED is capable of drawing as much as 60mA (at pea..
This is the Philips halogen CL 12v 10w. The base consists of a G4 with a 2 pin connector. This lamp has a T3 shape with an axial filament. It has a lo..