Say goodbye to unstable voltages with this LDO LD1117V33 linear regulator from STMicroelectronics. It has an overall accuracy of ±1 %. Its typical dro..
Optimize functionality in your circuit by placing this 3590S-2-103L potentiometer from Bourns at critical points. This product has a resistance value ..
A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a ES..
This is Adapter Breakout Board for ESP-32f ESP32 ESP-Wroom-32 Wireless Bluetooth Module. Adapter Board Pinboard Converter for ESP-32S ESP32S ESP32 Wir..
This is an easy, simple to use Passive IR (PIR) sensor – it only needs a single I/O pin on a microcontroller.or can be easily interfaced with relay or..
The RS232 to TTL converter module is widely used in radio modifications,phone flash, XBOX360 flash, GPS, vehicle detection, DVD flash, hard disk repai..
This is our heat shrink kit. We use it for all sorts of handy projects. Use it to reinforce connections, protect devices, and electrically isolate exp..
Product Description:
This is a newly designed product, using the Taiwan prolific production company PL2303HXD chips, PL2303HXD perfectly compatible w..
If you've started designing your own PCBs in Eagle or KiCad and want to make your PCB a reality, you may start out with an etching system to pattern o..
If you've started designing your own PCBs in Eagle or KiCad and want to make your PCB a reality, you may start out with an etching system to pattern o..
The Relay is a digital normally open switch that controls a relay capable of switching much higher voltages and currents than your normal Arduino boar..
This is an extremely accurate I2C real-time clock (RTC) with crystal compensation, inner chargeable battery. The SD2405AL is available in industrial t..
Op-amp coupled with MOSFET at outputWide power supply RangeSinge supply – 5V to 16VDual supply – ±2.5V to ±8VInput Terminal current: 1mAMaximum Output..
This SW-520D basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is upr..
The TEA2025B is a 2.5W per channel stereo audio amplifier, intended for use as a stereo or bridge mode audio amplifier in portable audio players. ..
This MOV is suitable for 220V AC line protection in a typical electronic devices against voltage surges and spikes, such as those generated by inducti..
DescriptionThis is a really simple vibration switch, it use very common in electronics toys, alarm, domestic appliance, electronics devices, smart hom..
This is your basic spool of leaded solder with a 63/37 water soluble resin core. 0.8mm gauge. Mechanic Brand. Sold in units of 50gTin(Sn):63%Lead(Pb):..
DescriptionMP3 module with simplified output directly to speakerCan be used in combination with Arduino UNO or any RX/TX moduleFully supports FAT16 , ..
This is an audio amplifier module with potentiometer with PAM8403 which is very efficient. To use it, all you need is a power supply between 3.6 V and..
10A axial rectifier diode with fast switching times suitable for general applications where a high current is required.Low reverse leakageHigh forward..
Punch in your secret key into this numeric matrix keypad. This keypad has 12 buttons, arranged in a telephone-line 3x4 grid. It's made of a thin, flex..
Interface: IIC/I2CGND: Power GoundVCC: 2.2V-5.5VSCL: CLK clock (High level 2.2V-5.5V)SDA: MOSI data (High level 2.2V-5.5V)Feature:Color: Blue and Yell..
The optical fingerprint scanner takes images of fingerprints and converts them into unique identifiers. The fingerprint scanner stores up to 128 diffe..
The antenna is best suited for GSM applications providing better signal strength with very small foam factor.Features:Frequency 700 ~ 2700 MHzS.W.R. &..
3.3V/3W smps Module (Hi-Link) is PCB mounted plastic enclosed isolated switching step-down power supply module. It can supply 3.3V DC from 100V AC - 2..
Very thin wall tubing good protection for temperature sensitive components.Low shrink temp improves production efficiency.Suitable for various electri..
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. T..
This is a breadboard adapter for the popular ESP-01/ESP-01S,ESP-01/ESP-01S NOT IncludedThis breadboard adapter will help you to make prototyping with ..
Breakthrough design, there are new breakthroughs, based on ESP-12E.The new four-layer board design.The new revision antenna RF performance optimizatio..
This is Adapter Breakout Board for ESP-32f ESP32 ESP-Wroom-32 Wireless Bluetooth Module. Adapter Board Pinboard Converter for ESP-32S ESP32S ESP32 Wir..
Introducing the Nano ESP32, a powerful addition to the Arduino ecosystem that brings the popular ESP32-S3 to the world of Arduino and MicroPython prog..
Breakthrough design, there are new breakthroughs, based on ESP-12E.The new four-layer board design.The new revision antenna RF performance optimizatio..
Specification:Brand newMicro USB type B Plug.Program ESP-WROOM-32 module without soldering.Provide all I/O pin for the ESP-WROOM-32 module.Build-in re..
This is Adapter Breakout Board for ESP-32f ESP32 ESP-Wroom-32 Wireless Bluetooth Module. Adapter Board Pinboard Converter for ESP-32S ESP32S ESP32 Wir..
This is a USB-TTL Serial Conversion with a Micro USB Module and is used as a shield to connect to the GPIOs on the ESP32-CAM board. The CH340C USB to ..
The ESP32-CAM has a very competitive small-size camera module that can operate independently as a minimum system with a footprint of only 27*40.5*4.5m..
The ESP32-S3 development board is assembled with an original ESP32-S3-WROOM-1 module from Espressif, with 16MB Flash and 8MB PSRAM (ESP32-S3-WROOM-1-N..
If you need to upload firmware into ESP12 or ESP07 modules before soldering into a final product, then this burn and test board from PMD Way is for yo..
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. T..
SIM7600 Series IntroductionThe LILYGO® SIM7600 development board combines the power of the ESP32-WROVER and SIM7600 modules, enabling high-speed LTE c..
T-Display-S3 is a development board whose main control chip is ESP32-S3. It is equipped with a 1.9-inch LCD color screen and two programmable buttons...
nanoESP32-C6 is a ESP32-C6 minimum system board designed and made by Muse Lab based on ESP32-C6-WROOM-1 module of Expressif. It features RGB LED, a BO..
OverviewThis is the NodeMCU development board based on ESP8266, features WiFi connectivity, onboard USB to UART converter and keys. What's more, all t..
The all new NodeMCU-32S with ESP32/CH340C Wifi Development Board - TYPE CThe NodeMCU-ESP32 is an ideal choice for effortless prototyping, offering eas..
The development board integrates the ESP8266 18650 battery. A standard 3000mah 18650 battery can run for 17 hours or more.Features:Compatible with nod..